明升体育在线

Back to Home | Site Map

Phone: 0577-62755895
  • Current Location : Home - Distribution type arrester - HY5WS- (3.8-17) / (15-50) Distribution type arrester
  • HY5WS- (3.8-17) / (15-50) Distribution type arrester

    Guide: HY5WS- (3.8-17) / (15-50) Distribution type arrester tags: arrester , HY5WS ,
    Clicks:
  • Product description and use method:

    HY5WS- (3.8-17) / (15-50) Distribution type arrester

    I. Overview

    Metal oxidation arresters are high-tech products in the 1990s internationally. It uses an oxygen zinc resistor with excellent non-linear volt-ampere characteristics. Therefore, the protection characteristics of the lightning arrester's streak, lightning wave, and operating wave are greatly improved compared to the traditional silicon carbide lightning arrester. In particular, zinc oxide resistors have good slope response characteristics, no delay to steep slope voltages, low operating residual voltage, and no discharge dispersion. In order to overcome the shortcomings of high discharge voltage caused by the delay of the discharge of the steep slope inherent to the SiC arrester, the high dispersion of the operating wave discharge results in the high discharge voltage of the operating wave, which greatly improves the protection margin under steep slopes and operating waves. In addition, in terms of insulation coordination, the protection margins of steep slopes, lightning waves, and operating waves can be made close to each other, thereby providing the best protection for power equipment and improving the reliability of protection. The zinc oxide lightning arrester has the ability to absorb lightning overvoltage, operating overvoltage and power frequency transient overvoltage at the same time.
    The composite jacket metal zinc oxide arrester is a high-tech product of the international 90s. It adopts integral silicone rubber molding, which has good sealing performance, excellent explosion-proof performance, pollution-resistant and no-clean, and can reduce the occurrence of wet flashes in foggy days, resists electrical corrosion and aging, is small in size, light in weight, and resistant to collision, and is easy to install and maintain. It is a new generation of porcelain arrester.


    Technical standards

    The standards for the production of products are GB11032-2000 (eqv IEC60099-4: 1991) "AC gapless metal oxide arresters" and JB / T8952-2005 "Composite jacket gapless metal oxide arresters for AC systems".


    Use environment

    1. Ambient temperature is -40 ℃ ~ + 40 ℃;
    2. The altitude does not exceed 2000m;
    3. Power frequency is 48Hz ~ 62Hz;
    4. The maximum wind speed does not exceed 35m / s;
    5. Seismic fissures of 7 degrees and below.
    The long-term applied voltage does not exceed its maximum continuous operating voltage.


    Product features

    1. Small size, light weight, collision resistance, no collision loss during transportation, flexible installation, especially suitable for use in switch cabinets;
    2. Special structure, integral molding, no air gap, good sealing performance, moisture-proof and explosion-proof;
    3.Large creepage distance, good water-increasing ability, strong pollution resistance, stable performance, reduce operation and maintenance;
    4. Unique formula of zinc oxide resistor chip, high capacity, low leakage;
    5. The actual DC reference voltage, square wave current capacity and high current withstand capability are higher than national standards.


    Five, product model description

    Six, appearance and installation dimensions

    Distribution type lightning arrester: It is used to protect the power distribution equipment, switch cabinet, box type transformer, power cable outlet, and pole switch of the corresponding voltage level from atmospheric overvoltage and operating overvoltage.

    Lightning arrester model

    System rated voltage

    Arrester rated voltage

    Continuous operating voltage

    DC reference voltage ( U1mA )

    Residual voltage under chirp surge current

    Residual voltage under lightning impulse current

    Residual voltage under operating impulse current

    Square wave flow capacity ( 2ms )

    High current shock resistance

    Drawing number

    kV (rms)

    kV

    kV

    A

    kA

    HY5WS-3.8 / 15 *

    3

    3.8

    2.0

    7.5

    17.3

    15

    12.8

    75

    40

    Figure 2

    HY5WS-5 / 15

    5

    4.0

    8.0

    17.3

    15

    12.8

    100

    65

    HY5WS-7.6 / 30 *

    6

    7.6

    4.0

    15.0

    34.5

    30

    25.5

    75

    40

    Figure 3

    HY5WS-10 / 30

    10

    8.0

    15.0

    34.5

    30

    25.5

    100

    65

    HY5WS-12.7 / 50 *

    10

    12.7

    6.6

    25.0

    57.5

    60.0

    38.5

    75

    40

    Figure 4

    HY5WS-17 / 50

    17

    13.6

    25.0

    57.5

    60.0

    38.5

    100

    65


    Note: 1. "*" is the old standard model.

  • Previous: No
  • Next: No
related product recommendation
Copyrght 2010-2012 Yueqing Chuantai Power Equipment Co., Ltd. All Rights Reserved Tel: 0577-62755895 Fax: 0577-62759767 Mobile: 13986710797 Zhejiang ICP No. 11039091-1
This site provides professionally: high-quality fuses , high-voltage wall bushings , high-voltage load switches , high-voltage insulators, and other high-quality products of various specifications, as well as industry knowledge and various information. Thank you for your visit and attention!